Maytag Appliance Repair
We repair Maytag appliances in Edmonton & surrounding area
Dial An Applianceman is a family-owned and operated home appliance repair service that has been serving Edmonton and the surrounding regions for over 40 years. We offer great service, reasonable price, same-day service, and complete customer satisfaction! Our skilled experts can be at your home within a day to fix your Maytag appliance. We will do our best to provide same-day service if you contact us. Our journeyman technician will arrive to analyse the issue and repair your appliance. If our technician does not have the part on hand, we will order it and return as soon as it arrives.
Dial An Applianceman – Edmonton
Maytag Appliance Repair Service – Maintenance – Installation
780-964-7861
40+ years servicing Edmonton & surrounding areas
Edmonton Maytag Appliance Repair Experts
We offer same-day or next-day repairs
Fully Licensed, Insured & Bonded Technicians
*Yes, we install Maytag appliances in Edmonton & surrounding areas
Many of our professionals have extensive knowledge of all Maytag appliances. If your Maytag appliance isn’t operating correctly, contact our certified Maytag appliance repair technicians. Our technicians are licensed, insured, and bonded. We are the best option among Maytag appliance repair service providers in Edmonton and the nearby areas. Our expert appliance repair service team is constantly trained to service all Maytag appliances, including dryers, washers, ranges, dishwashers, refrigerators, microwaves, cooktops, freezers, and wall ovens. They can repair any Maytag appliance, wherever you bought it.
Whatever the issue is with your residential or commercial Maytag appliance, our professionals can diagnose it. They will provide you with a repair cost estimate as soon as the defect is identified. We ensure that our pricing is fair and affordable. We always provide warranty on our work. Dial An Applianceman is always available to assist you, no matter what problem you are experiencing or what Maytag appliance you own – we are the total home appliance repair company.
The satisfaction of our consumers is our top concern. We provide a wide range of home Maytag appliance repair services. Whatever happens to your Maytag appliance, anytime you need us, call us and we will relieve you of your appliance repair difficulties as fast and effectively as possible. Among Edmonton’s repair service providers, we are without a doubt the best at delivering home Maytag appliance repair services. Our comprehensive knowledge, dedication for quality and safety, as well as great performance and precision, are always available to you.
Customer satisfaction is our number one priority at Dial An Applianceman. We think that customer service is about making sure you’re satisfied at every stage of the process. We have systems in place to guarantee that your appliance servicing experience is hassle- and worry-free, from the minute you phone our Customer Service Representative to the moment your appliance is operational again. Our mission is to deliver high-quality, dependable, and reasonably cost appliance servicing. If you’re not sure where to start when it comes to mending your appliance, let us handle the diagnostic and repair. We’ll have your appliance operational in no time. We service the entire Edmonton metro area including Spruce Grove appliance repair, St Albert appliance repair, Leduc appliance repair, and Sherwood Park appliance repair.
Frequently Asked Questions
Why isn’t my top load Maytag washing machine not spinning?
A common cause is due to an uneven load or jammed clothing. If those are fine, the next thing to inspect is the lid switch. The switch prevents the washer from spinning while the lid is open. Finally, check the drive belt and see if it is broken, damaged or loose.
My Maytag dryer is not heating?
Check the incoming power with the proper voltage. The dryer needs 240 volts at the receptacle. Another common thing to inspect is the exhaust vent and to see how much airflow is available. More common issues include a faulty thermal fuse, defective heating element, faulty high limit thermostat or faulty thermostat. If your dryer is gas check the igniter or the solenoid coils.
What is the service window for an appointment?
When you call to make an appointment, we will provide you with a 3-hour window. If you need a 30-minute notice, let us know when booking the appointment and our repairman will call you in advance of their arrival. We know how important your time is, that is why we do our utmost to be punctual.
We have specialised in Maytag appliance repair and servicing for over 30 years. We take satisfaction in being able to say that we have thousands of satisfied clients who appreciate our speedy and high-quality services. We make the process of fixing your device as simple as possible. Our trained, experienced and reliable specialists will offer you with the best appliance repair service in Edmonton, as well as free maintenance advice if necessary. We even offer commercial appliance repair in Edmonton!
Maytag Front Load Washer Error Codes
| Error Code | Definition | Solution |
|---|---|---|
| LOC or LC | Control Lock has been activated | Touch the Control Lock button, or (on older models) determine which button activates control lock from your Owner’s Manual. Some models require you to press and hold the button. |
| dET | Detergent cartridge not detected in the dispenser. | This is on select models. If you are using single-load doses of detergent, ignore this message. Ensure the dispenser cartridge is inserted correctly and the dispenser drawer is shut completely. |
| Int | The cycle was paused or canceled. | The washer may take 20 to 30 minutes to stop spinning and drain. To remove the code, press pause or cancel twice and power once. If still displayed, unplug for 5 minutes. |
| rL or F34 | Items detected during Clean Washer cycle | Remove items from the drum and restart the cycle. |
| Sud or Sd | Too many suds | Washer extends rinse time to remove suds. Use HE detergent only. Avoid “no splash” bleach. Check drain hose for clogs or kinks. |
| F5 E2 | Door not locking properly | Ensure door is clear and fully closed. Press Pause/Cancel twice and Power once. |
| F7 E1 | Motor speed sensing error | Check shipping bolts are removed and washer is not overloaded. Reset by pressing Pause/Cancel twice and Power once. |
| F8 E1 or LO FL | Low water flow detected | Ensure water supply is on, hoses are not kinked, and valves are open. |
| F8 E2 | Dispenser system issue | Ensure detergent drawer is not clogged. |
| F9 E1 | Drain time too long | Check drain hose for clogs or kinks. Ensure proper standpipe height. Use HE detergent to avoid excess suds. |
| Other F# E# | General error | Unplug washer for 5 minutes, reconnect, and restart cycle. If issue persists, contact service. |
Maytag Dishwasher Error Codes
| Error Code | Definition | Solution |
|---|---|---|
| E:15 | The E-15 Error Code could indicate a small leak from the dishwasher. | Inform the customer to turn the water off to the Dishwasher and schedule service. |
| E1 | Your dishwasher could be siphoning. | Make sure to connect the drain hose to the waste tee or disposer inlet above the drain trap in the house plumbing, and 20″ (50.8 cm) minimum above the floor. |
| E3 | Cycle power to reset the control panel. | To reset the dishwasher control panel, disconnect it from the power source for 30 seconds. If your dishwasher is plugged into an outlet, simply unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off at the home electrical panel that powers the dishwasher for 30 seconds and then turn the breaker back on. |
| F8E4 | 1. Is the water supply connected correctly? | Check all the connection points. Ensure the rubber washer is properly seated in the fitting to the connection point. Contact us for assistance. |
| F8E4 | 2. Is the float switch connected? | Ensure the float switch is properly connected. Also, ensure that the power supply wire or cord does not touch the dishwasher motor or the lower part of the dishwasher tub. Reconnect the float switch by aligning the connector with the connector housing and pushing in until the locking tab is visible over the back of the connector. |
| F8E4 | 3. If you see water in the drip tray, it needs to be emptied. | To remove the drip pan assembly, press the snap at each side of the plastic tray in toward the center of the product and pull toward yourself. Be careful not to pull too far or too hard, as the float switch wire is still connected. Pulling too far or too hard can damage the wire. |
| E6 | Reset the dishwasher control panel. | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. |
| E7 | Reset the dishwasher control panel. | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. |
| F1E1 | Drain sequence begins but dishwasher does not continue to operate. | Turn off water to the unit (if possible). Turn off power to the unit. If the water cannot be turned off, keep the power on and the door closed. Press Cancel key one time to silence alarm tone. |
| F2E2 | Reset the dishwasher control panel. | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. |
| F3E2 | Reset the dishwasher control panel. | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. |
| F4E3 | Reset the dishwasher control panel. | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. |
| F6E1 | The product is either unable to start or resume cycles. | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. If new cycle cannot be started and the error code remains, contact us for service. |
| F6E3 | Check for foam or suds at bottom of dishwasher. | If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly or may not fill with water. Excess suds can be caused by using the incorrect type of detergent, such as laundry detergent, hand soap, or dish detergent for hand washing dishes; not replacing the rinse aid dispenser cap; or using an excessive amount of dishwasher detergent. |
| F6E4 | Is the dishwasher level? | Incorrect leveling of the dishwasher can cause this error. Incorrect leveling can actuate the overfill / floater switch and cause the error. |
| F7E2 | Error code | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. If new cycle cannot be started and the error code remains, contact us for service. |
| F8E2 | Error code | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. If new cycle cannot be started and the error code remains, contact us for service. |
| F8E5 | Drain sequence begins but machine does not operate. | Turn off water to the unit (if possible). Turn off power to the unit. If the water cannot be turned off, keep the power on and the door closed. Press Cancel key one time to silence alarm tone. If you are unable to turn off the water supply, turn off power to the dishwasher. |
| F9E1 | Error code | Disconnect from power source for 30 seconds. If dishwasher is plugged in to an outlet, unplug the unit for 30 seconds and then plug the unit back in. If the dishwasher is hard-wired to the power supply, turn the breaker off on the electrical panel for 30 seconds and then turn the breaker back on. If new cycle cannot be started and the error code remains, contact us for service. |
| F9E2 | Has the garbage disposal knockout plug been removed? | If the dishwasher is connected to a garbage disposal, ensure the knockout plug has been removed from the disposal inlet. |
| FAE5 or F10E5 | Cycle ends and drains but displays the error code. | Press the “Cancel” key twice. Try to start a new cycle |
| H2O | Cycle is paused. | 1. Ensure water supply to the dishwasher is turned on. 2. Check to make sure there are no kinks in the water supply hose. 3. Press start and the dishwasher will attempt to fill and resume cycle. |
Dial An Applianceman – Edmonton
Maytag Appliance Repair Service – Maintenance – Installation
780-964-7861
40+ years servicing Edmonton & surrounding areas
Edmonton Maytag Appliance Repair Experts
We offer same-day or next-day repairs
Fully Licensed, Insured & Bonded Technicians
*Yes, we install Maytag appliances in Edmonton & surrounding areas
Author: